Te Pari Sheep Jetter Instruction Manual

Thank you for purchasing a Te Pari Sheep Jetter. This guide contains all the necessary information to help you set up your equipment and begin your first jetting session. For additional information, please contact us using the details provided on our website.

Please read and understand the instructions before operating your Te Pari Sheep Jetter.

At Te Pari we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical/mechanical appliance and adhere to the following precautions.

Read these instructions before use and save them for future reference.

• Remove any packaging material and promotional stickers before using the Te Pari Sheep Jetter for the first time.
• Always make sure the Te Pari Sheep Jetter is completely assembled before operating.
• Ensure the Te Pari Sheep Jetter is turned off at the power switch, before removing the battery. Always secure the inlet hose onto the cam-lock before starting the pump.
• Do not attempt to operate the Te Pari Sheep Jetter by any method other than those described in these instructions.
• Do not pump hot or boiling liquids.
• Do not run the Pump without liquid in the supply tank.
• Always ensure the Te Pari Sheep Jetter is turned off at the power switch and battery disconnected before attempting to move the appliance, when not in use if left unattended or before disassembling, cleaning or sorting.
• Do not use the Te Pari Sheep Jetter on uneven surfaces.
• Do not leave the Te Pari Sheep Jetter unattended when in use.
• Keep the Te Pari Sheep Jetter clean. Follow the cleaning instructions provided in this manual.
• Carefully read all supplied engine/pump instructions to ensure safe operation and avoid possible damage or reduced engine/pump life.

• Unwind supply hoses before use.
• Do not let the power cords be submerged in hot or wet surfaces or become knotted.
  The Te Pari Sheep Jetter is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the Te Pari Sheep Jetter by a person responsible for their safety.
• It is recommended to regularly inspect the Te Pari Sheep Jetter. Do not use the Te Pari Sheep Jetter if the power supply cord, pump, hoses or Te Pari Sheep Jetter becomes damaged in any way. Return the entire Te Pari Sheep Jetter to the nearest authorized Te Pari Service Centre for examination and/or repair.
• Any maintenance other than that specified in this booklet should be performed by an authorized Te Pari Service Technician.
• Do not use the Te Pari Sheep Jetter for anything other than its intended use.

Setting up your Te Pari Sheep Jetter

1. Fully Charge the 12VDC battery before use.
2. Place the Jetter on a firm and level surface in an appropriate location that will allow your animals to travel freely into the Jetter.
3. Line up gates/race to the inlet and outlet of the Jetter
4. Making sure the Jetter is turned off, connect the battery (12VDC) to the control unit.
5. Connect the outlet of the pump to the hose tail on the Jetter. Connect the inlet of the pump to the tank outlet and prime the pump if required (Refer to the user manual for the pump you're using). Make sure all connections are securely connected.
6. Open any valves between the storage tank and Jetter and start your pump.
7. Switch the “Power” switch to “on” and “Nozzle Selection” switch to “both” on the control box attached to the Jetter.
8. Prime the Jetter by pushing the “ManualSpray” button on the control box. Keep priming the system until all air bubbles have been removed from the system and the pump has built up pressure.
9. If desired switch the “Nozzle Selection” switch to either “top” or “btm” if required.
10. Using the “manualSpray” button adjust the flow/pressure of your pump until you get the desired output flow & pressure.

Running the Jetter

1. Depending on your setup open any gates etc. and allow your animals to enter the Jetter in a single file.
2. We recommend running the motor at around ¾ throttle to get between 60 – 90 psi.
3. The sensors in the Jetter will pick up when an animal enters and opens the selected valves to apply spray to the required area.

Packing up your Te Pari Sheep Jetter

1. Flush the Jetter with clean water.
2. Turn your pump off.
3. Push the “Manual Spray” button to release any pressure in the spray lines.
4. Turn the “Power” switch to “off”.
5. Close and valves on the tank and disconnect the hoses from the Jetter.
6. Wash down and dry the Jetter to clean off the overspray.
7. Pack up the Jetter and store it in a dry place.

To keep your Te Pari Sheep Jetter working efficiently proper care, cleaning and storage need to be maintained.

Care

Before each use inspect all parts of the Jetter to check for any damage that has occurred. Move and lift the Jetter using the correct lifting points and handles. Following all instructions outlined in this booklet.

Cleaning

After each use of the Jetter flush all the lines with clean water to remove any spray that could cause damage to the pipework if left for an extended amount of time. Wash down the Jetter to remove any overspray of chemicals, dirt and grime that has built up during use and transport. Check nozzles for build-up of grime and clean accordingly.

Storage

Disconnect the battery from the Jetter before storing it and switch the unit off. Drain as much liquid from the unit as possible and fully dry the Jetter and store the Jetter in a clean, dry area that is not subject to the elements.

• Please check this troubleshooting guide before ringing customer support, as often something quite simple could be the problem.
• A service charge will be made for callouts if the fault is not covered by your warranty.
• For your safety, and that of others, never leave the unit operational when not attended.